TI,TI公司,TI代理商
TI(德州仪器)| TI产品型号搜索
专营TI元器件,强大的现货交付能力,解决您的采购难题
全流程提供TI现货供应链服务
当前位置:TI公司 > > TI芯片 >> SN65LVPE501
SN65LVPE501技术文档下载:
SN65LVPE501技术文档产品手册下载
SN65LVPE501 - 产品图解:
SN65LVPE501-双通道 x1 PCI Express Gen II 转接驱动器/均衡器
承诺原装正品
专营TI,真正优化您的供应链
TI产品 - SN65LVPE501介绍
SN65LVPE501 - 双通道 x1 PCI Express Gen II 转接驱动器/均衡器

SN65LVPE501是TI公司的一款USB信号调节器产品,SN65LVPE501是双通道 x1 PCI Express Gen II 转接驱动器/均衡器,本页介绍了SN65LVPE501的产品说明、应用、特性等,并给出了与SN65LVPE501相关的TI元器件型号供参考。

SN65LVPE501 - 双通道 x1 PCI Express Gen II 转接驱动器/均衡器 - USB信号调节器 - USB - TI公司(Texas Instruments,德州仪器)

产品描述

The SN65LVPE501 is a dual channel, single lane PCIe redriver and signal conditioner supporting data rates of up to 5.0Gbps. The device complies with PCIe spec revision 2.1.

Programmable EQ, De-Emphasis and Amplitude Swing

The SN65LVPE501 is designed to minimize the signal degradation effects such as crosstalk and inter-symbol interference (ISI) that limits the interconnect distance between two devices. The input stage of each channel offers selectable equalization settings that can be programmed to match loss in the channel. The differential outputs provide selectable de-emphasis to compensate for the anticipated distortion PCIe signal will experience. Level of de-emphasis will depend on the length of interconnect and its characteristics. Both equalization and de-emphasis levels are controlled by the setting of signal control pins EQ1, EQ2 and DE1, DE2.

To provide additional control of signal integrity in extended backplane applications LVPE501 provides independent output amplitude control for each channel. See for setting details.

Device PowerOn Device initiates internal power-on reset after VCC has stabilized. External reset can also be applied at anytime by toggling RST pin. External reset is recommended after every device power-up. When RST is driven high, the device samples the state of EN_RXD, if it is set H device enters Rx.Detect state where each channel will perform Rx.Detect function (as described in PCIe spec). If EN_RXD is set L, automatic RX detect function is disabled and both channels are enabled with their termination set to ZDC_RX.

Receiver Detection While EN_RXD pin is H and device is not in sleep mode (RST is H), SN65LVPE501 performs RX.Detect on both channels indefinitely until remote termination is detected on both channels. Automatic Rx detection feature can be forced off by driving EN_RXD low. In this state both channels input termination are set to ZDC_RX.

Sleep (Shut_Down) Mode This is low power state triggered by RST = L. In sleep mode receiver termination resistor for each of the two channels is switched to ZRX-HIGH_IMP of >50 KΩ and transmitters are pulled to Hi-Z state. Device power is reduced to <1mW (TYP). To get device out of sleep mode RST is toggled L-H.

Electrical Idle Support A link is in an electrical idle state when the TX± voltage is held at a steady constant value like the common mode voltage. SN65LVPE501 detects an electrical idle state when RX± input voltage of the associated channel falls below VEID_TH min. After detection of an electrical idle state in a given channel the device asserts electrical idle state in its corresponding TX. When RX± voltage exceeds VEID_TH max, normal device operation is restored and output starts passing input signal. Electrical idle exit and entry time is specified at ≤6ns.

Electrical idle support is independent for each channel.

Power Save Features The device supports three power save modes as described below.

1. Sleep (Shut_Down) Mode

This mode can be enabled from any state (Rx detect or active) by driving RST L. In this state both channels have their termination set to ZRX-HIGH_IMP+ and outputs are at Hi-Z. Device power is 1mW (MAX)

2. Auto Low Power Mode

This mode is enabled when PS pin is tied H and device is in active mode. In this mode anytime Vindiff_pp falls below selected VEID_TH for a and stays below VEID_TH for >1µs (TYP), the associated CH will enter auto low power (ALP) mode where power/CH will be reduced to <1/3rd of normal operating power/CH or about 70mW under typical voltage of 3.3V when ALP conditions are met for both channels. A CH will exit ALP mode whenever Vindiff_pp exceeds max VEID_TH for that channel. Exit latency is 30ns max. To use this mode link latency will need to account for the ALP exit time for N_FTS. ALP mode is handled by each channel independently based on its input differential signal level. This mode can be disabled by leaving PS as NC or tying PS to GND via 4.7kύ.

3. Cable Disconnect Mode

This mode is activated when RST is H, EN_RXD = H, and no termination is detected by either channel. Device is in the Rx.Detect state whereby it is continuously performing Rx.Detect on both channels. In this state total power consumed by device is typically <3% of normal active power. Or <10mW (MAX).

Beacon Support With its broadband design, the SN65LVPE501 supports low frequency Beacon signal (as defined by PCIe 2.1 spec) used to indicate wake-up event to the system by a downstream device when in L2 power state. All requirements for a beacon signal as specified in PCI Express specification 2.1 must be met for device to pass beacon signals.

Devic Power

The SN65LVPE501 is designed to operate from a single 3.3V supply. Always practice proper supply sequencing procedure. Apply VCC first before any input control pin signals are applied to the device. Power-down sequence is in reverse order.

产品特性

  • Single Lane PCIe Equalizer/Redriver
  • Support for Both PCIe Gen I (2.5Gbps) and Gen II (5.0 Gbps) Speed
  • Selectable Equalization, De-emphasis and Output Swing Control
  • Integrated Termination
  • Hot-Plug Capable
  • Receiver Detect
  • Low Power:
    • 330mW(TYP), VCC = 3.3V
  • Auto Low Power Modes:
    • 5mW (TYP) When no Connection Detected
    • 70mW (TYP) When in Auto-Low Power Mode
  • Excellent Jitter and Loss Compensation Capability:
    • 30" of 6 mil Stripline on FR4
  • Small Foot Print – 24 Pin 4 × 4 QFN Package
  • High Protection Against ESD Transient
    • HBM: 3,000 V
    • CDM: 1,500 V
    • MM: 200 V

下面可能是您感兴趣的TI公司USB信号调节器元器件
  • MSP430FR6820 - MSP430FR687x、MSP430FR682x 、MSP430FR587x 混合信号微控制器
  • SN5447A - BCD 到 7 段解码器/驱动器
  • TLV5614-EP - 增强型产品四路 Dac,具有串行输入、可编程建立时间、低功耗、硬件或软件电源关闭功能
  • DS110DF1610 - DS110DF1610 8.5 至 11.3 Gbps 16 通道重定时器
  • DAC8168 - 具有 2.5V、2ppm/℃ 内部参考的 14 位、八通道、超低短时脉冲波形干扰、电压输出 DAC
  • SN54153 - 双路 4 线路到 1 线路数据选择器/多路复用器
  • SN74F27 - 三路 3 输入正或非门
  • ADS7891 - 具有 Ref 引脚的 2.7V-5.25V 数字 5V 模拟 14 位 3MSP 并行 ADC
  • SN75LVDS32 - 四路高速差动接收器
  • SN74ALVCH162268 - 具有三态输出的 12 位至 24 位寄存总线交换器
  • 节约时间成本,提高采购效率,TI官网授权代理
    TI公司|TI德州仪器|德州仪器TI公司代理商|TI芯片代理商
    TI公司产品现货专家,订购TI公司产品不限最低起订量,TI产品大陆现货即时发货,香港库存3-5天发货,海外库存7-10天发货
    寻找全球TI代理商现货货源 - TI公司(德州仪器)电子元件在线订购