• Control Inputs VIH/VIL Levels Are Referenced to VCCA Voltage
• VCC Isolation Feature – If Either VCC Input Is at GND, All Are in the High-Impedance State
• Fully Configurable Dual-Rail Design Allows Each Port to Operate Over the Full 1.65-V to 5.5-V Power-Supply Range
• Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II
• ESD Protection Exceeds JESD 22
  • 4000-V Human-Body Model (A114-A)
  • 200-V Machine Model (A115-A)
  • 1000-V Charged-Device Model (C101)
• SUPPORTS DEFENSE, AEROSPACE, AND MEDICAL APPLICATIONS
  • Controlled Baseline
  • One Assembly/Test Site
  • One Fabrication Site
  • Available in Military (–55°C/125°C) Temperature Range(1)
  • Extended Product Life Cycle
  • Extended Product-Change Notification
  • Product Traceability

(1) Additional temperature ranges are available – contact factory

DESCRIPTION/ORDERING INFORMATION

This 8-bit noninverting bus transceiver uses two separate configurable power-supply rails. The SN74LVC8T245 is optimized to operate with VCCA and VCCB set at 1.65 V to 5.5 V. The A port is designed to track VCCA. VCCA accepts any supply voltage from 1.65 V to 5.5 V. The B port is designed to track VCCB. VCCB accepts any supply voltage from 1.65 V to 5.5 V. This allows for universal low-voltage bidirectional translation between any of the 1.8-V, 2.5-V, 3.3-V, and 5.5-V voltage nodes.

The SN74LVC8T245 is designed for asynchronous communication between two data buses. The logic levels of the direction-control (DIR) input and the output-enable (OE) input activate either the B-port outputs or the A-port outputs or place both output ports into the high-impedance mode. The device transmits data from the A bus to the B bus when the B-port outputs are activated, and from the B bus to the A bus when the A-port outputs are activated. The input circuitry on both A and B ports is always active and must have a logic HIGH or LOW level applied to prevent excess ICC and ICCZ.

The SN74LVC8T245 is designed so that the control pins (DIR and OE) are supplied by VCCA.

This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down.

The VCC isolation feature ensures that if either VCC input is at GND, all outputs are in the high-impedance state.

To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.

• LP38690 - 借助陶瓷输出电容实现稳定的 1A 低压降 CMOS 线性稳压器
• TPD12S016 - 用于便携应用的超值 HDMI 配套芯片
• BQ24018 - 用于便携式应用的单芯片锂离子充电管理 IC (bqTINY)
• ISO7320C - 耐用 EMC 低功耗双通道数字隔离器
• SN74V3680 - 16384 x 36 同步 FIFO 存储器
• DS26C32AMQML - CMOS Quad Differential Line Receivers
• MSP430F247 - 16 位超低功耗微控制器，具有 32KB 闪存、4KB RAM、12 位 ADC、2 个 USCI 和 HW 乘法器
• LM4040B30 - 3V 精密微功耗并联电压参考，0.2% 精确度
• SN54LVC573A - 具有三态输出的八路透明 D 类锁存器
• UC3717A - 步进电机驱动电路